Quick Setup Guide




Unbox T100, Router, Long Range Antenna, Ethernet Cable, Battery, and Split Power Cable.

  1. Connect the ORANGE end of Split Power Cable to the DC OUT port on the Battery.  The light on the Battery should illuminate.

    NOTE: Make sure the Battery is set to 12 VOLTS
    FAILURE TO DO THIS CAN CAUSE DAMAGE TO YOUR EQUIPMENT.   
  2. Connect the BLACK end of Split Power Cable to the DC IN port on the T100.
  3. Connect the YELLOW end of Split Power Cable to the power port on your Router.
  4. Connect the GRAY Ethernet Cable from the LAN port on the back of the T100 to PORT 1 on your Router.
  5. Connect the BLACK Antenna Cable between the Long Range Antenna and the Router.
  6. Power ON your Router and wait for Power, 5.0 and 2.4 to light up.
  7. After your Router has booted up, Power ON your T100 and wait for the STATUS light to turn Solid GREEN. 
  8. Power ON your Camera and connect it to the HDMI IN port on the front of the T100.  NOTE: Connect necessary mini or micro HDMI adapter for your camera.
  9. If Record light is blinking, check Camera’s cables and adapters for a loose connection.
  10. Connect your iPad(s) to the echo 5 - (school name) wifi network.
    NOTE: echo 2 wifi network interferes with headsets and should NOT be used.
  11. Open the echo1612 app on your iPad and select the T100 from the nearby computers window and turn on Download Clips (top right corner of echo1612 app). 
  12. Press Record on the front of the T100. The Record LED should turn ORANGE.
    NOTE: If your Orange LED is blinking, check the camera/cables for a loose connection.

The new clip should appear on your iPad(s) within 5-10 seconds of stopped recording.




Adding a second T100 with the Range Extender

Unbox Secondary T100, Range Extender, Long Range Antenna, Ethernet Cable, Battery & Split Power Cable.

  1. Connect Secondary T100 & Range Extender to your Battery using the Split Power Cable.
  2. Connect the BLUE Ethernet Cable from the LAN port on the back of T100 to PORT 1 on your Range Extender.
  3. Power ON your Range Extender (it might take a few minutes).
  4. (First Time Setup For Range Extender) Press the Scan Button on the screen and select the echo 2 and echo 5 networks from the lists. Enter your Router’s password when prompted.

    NOTE: The first time setup might take a few minutes and we recommend you setup the Range Extender for the first time in the same room as the router.

    When the Range Extender asks to create a network, select CLONE SETTINGS and continue.

    Once the Range Extender reboots, verify that the Wired Port Settings are on 5GHZ.

    From the Range Extender home screen, press SETTINGS > NETWORK SETTINGS > WIRED PORT ROUTING > 5GHZ > APPLY
  5. If your using a Preview Screen/TV, plug it into the HDMI OUT port on the back of T100.
    NOTE: If you do not see video on your preview screen while your T100 is powered on, please restart your T100 with your preview screen connected.
  6. Power ON your Secondary T100.
  7. Connect your Camera to the HDMI IN port on the T100.
  8. Power and Status lights should be Solid GREEN.
  9. If Record light is blinking, check your Camera’s cables & adapters for a loose connection.
  10. Press Record on Primary T100.  The Secondary T100 will start recording simultaneously.
  11. Verify all iPads are connected to the Primary T100 on the Nearby Computers window.
  12. To toggle between the angles on your iPad, press the [ 1 ] [ 2 ] buttons in the top left of the echo iPad app.



Adding a second T100 in the same room as the primary T100

Unbox Secondary T100, Long Range Antenna, Ethernet Cable, Battery, & Split Power Cable.

  1. Connect your Secondary T100 to your Battery using the Split Power Cable.
  2. Connect the Ethernet Cable from the LAN port on back of the T100 to PORT 2 on Router.
  3. Power on Router.  NOTE: It may take a few minutes.
  4. If using a Preview Screen or TV, plug it into the HDMI OUT port on the back of the T100.
    NOTE: If you do not see video on your preview screen while your T100 is powered on, please restart your T100 with your preview screen connected.
  5. Power on your Secondary T100.
  6. Connect your Camera to the HDMI IN port on the T100.
  7. Power and Status lights should be Solid GREEN.
  8. If Record light is blinking, check your Camera’s cables & adapters for a loose connection.
  9. Press Record on your Primary T100.  The 2nd T100 should start recording simultaneously.
  10. Verify all iPads are connected to the Primary T100 on the Nearby Computers window.
  11. To toggle between angles on iPad, press the [ 1 ] [ 2 ] buttons in the top left of the echo iPad app.



Troubleshooting

If the above steps are followed correctly there should be no issues concerning the T100 Replay System.  If you do experience any system malfunction there are a few steps to correct the problem.

  1. Power DOWN the T100(s) and Router
  2. Close the echo1612 app on your iPad(s)
  3. Unplug HDMI and power cables for a few seconds and then replug.
  4. Power Router back up and then Power ON the T100(s) and re-open the echo1612 app.